Graffiti removal for use on the exteriors of trains, metros and trams.

Application instructions

Apply product with a brush or paintbrush. Apply the product in sections and do not apply so many m2 that the product is at risk of drying. Approx. 10 – 30 m2 is recommended depending on weather and temperature. Allow the product to work for 5 – 20 minutes depending on the nature of the graffiti. Use a brush or paintbrush on the surface to ensure that the paint is dissolved. White nylon scouring pads that do not scratch can be used to treat and remove any “paint drops” from spray paint graffiti. Then wash off the surface thoroughly using a soft brush and running water or a hot water pressure washer and low pressure. For thick layers of graffiti, it can be necessary to repeat the treatment and for large amounts of Tectyl graffiti, it can be necessary to use GR Tectyl M.

Note: Never apply on hot surfaces and prevent drying.
Use caution on repainted and sensitive metal and plastic surfaces.
Sample washing is recommended.

Dosage

The product is used in concentrated form. Consumption approx. 0.3 – 0.5 litre/m2.

Packaging

380010 – 10L
380700 – 1000L

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Graffiti Remover Train F appeared first on Blue and Green.

Eco-labeled product for removing graffiti from exterior surfaces of trains, metro, and trams

Application instructions

Apply the product using a brush.
Work in sections and avoid covering too many m² at once to prevent the product from drying out. Approximately 10–30 m² is recommended, depending on weather and temperature.
Allow the product to act for 5–20 minutes depending on the nature of the graffiti. Work the surface with a brush to ensure the paint dissolves.
White scrub pads that do not scratch can be used to work on and remove any “paint drips” from spray graffiti.
Then rinse the surface thoroughly using a soft brush with water flow or a low-pressure hot water pressure washer.
In cases of thick graffiti layers, it may be necessary to repeat the treatment. For graffiti involving heavy-duty undercoating (tectyl), the use of GR Tectyl M may be required.

Guidelines
Never apply on hot surfaces and prevent the product from drying.
Exercise caution on repainted or sensitive metal and plastic surfaces.
Test washing is recommended.

Dosage

Use the product undiluted. Consumption: approx. 0.3–0.5 liters/m².
Be environmentally conscious: do not use more than necessary.

Packaging

777010 – 10L
777025 – 25L
777700 – 1000L

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Eco Graffiti Remover Train appeared first on Blue and Green.

GR Blue is used to remove graffiti from absorbent surfaces such as brick, granite, concrete, marble, terrazzo, slate, sandstone, limestone, tiles etc.

Advantages

• Effective on both spray doodles, felt-tip pens and tectyl
• Slight odor
• Thin liquid
• Easy to rinse off
• Economical in use

Application instructions

Apply the product with a paintbrush, brush, roller or paint sprayer. Allow the product to work for 10 – 2 hours depending on the nature of the graffiti. Use a brush or paintbrush on the surface to ensure that the paint is dissolved. Then wash off the surface thoroughly using a hot water pressure washer and adjust the pressure to the facade. In cases where a “shadow” remains, it can be necessary to use either GR Shadow or GR Kilroy.

Note: Never apply on hot surfaces and prevent drying.
Use caution on repainted and sensitive metal and plastic surfaces.
Sample washing is recommended.

Dosage

The product is used in concentrated form. Consumption approx. 0.3 – 0.5 litre/m2.

Packaging

331025 – 25L
331700 – 1000L

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Graffiti Remover Blue Flytande appeared first on Blue and Green.

A very effective graffiti and shadow remover to be used in cold weather and on difficult graffiti. Can be used on porous surfaces such as: granite, brick, concrete, lime, tiles, etc. The product dissolves spray graffiti, permanent markers and marker scribbles. For use on porous external surfaces.

Note! Do not use on metal surfaces such as aluminum. Do a test before removal.

Advantages

– Combination product
– Efficient

Application instructions

Apply with a brush. Agitate the surface well. Leave until the graffiti is dissolved, 10-30 minutes depending on the surface, graffiti and weather conditions. Rinse with hot water and high pressure, 90°C, 150 bar/2175 PSI or adapt to the surface. The spread of the lance nozzle should be 15 – 25 degrees and the water flow should be 15 to 20 liters/minute (4-5 gal/minute). For shadows, apply as a shadow remover, wait 5-10 minutes before rinsing with high pressure. Final rinse with low pressure.
Store frost-free in closed original packaging.

Note: Never apply on hot surfaces and prevent drying.
Use caution on repainted and sensitive metal and plastic surfaces.
Sample washing is recommended.

Dosage

Used concentrated.
Shake/stir before use

Consumption: 0.5 – 1.0 litres/m²

Packaging

026010 – 10L

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Graffiti Remover Eden Gel appeared first on Blue and Green.

Used to remove graffiti from industrial painted surfaces such as trains, subways, trams, buses, metal facades, etc.
Works great even on absorbent materials where you have a sensitive painted surface to take into account when cleaning.

Advantages

– Effective on spray paint and marker graffiti.
– Gentle on underlying surfaces and materials
– Subtle scent
– Economical

Application instructions

Påfør produktet med en klut eller pensel og prøver å tørke vekk graffiti umiddelbart – etter tørking / skyll overflaten med vann.
Ved vanskeligere tagging / graffiti. la det virke i maksimalt 15 minutter og bearbeid overflaten med en klut eller børste for å sikre at fargen er oppløst.
Etter tørk / skyll overflaten grundig med vann slik at produktet slutter å virke på det underliggende materialet.

Forskrift: Påfør aldri på varme overflater og hindre uttørking. Vær forsiktig på overmalte og følsomme metall- og plastoverflater. Prøvevask anbefales.

Dosage

The product is used in concentrated form. Consumption approx. 0.1 – 0.3 litre/m2.

Packaging

336006 – 5L
336010 – 10L
336025 – 25L
336700 – 1000L

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Graffiti Remover 21 Flytande appeared first on Blue and Green.

Graffiti remover. Used to remove marker, ink, spray paint, etc. Mr. Perfect is used on all hard and soft colourfast and material-based surfaces such as floors, facades, tiles, metals, textiles, etc.

Advantages

• Low odor
• Aromatic free

Application instructions

Leave the product on for 1-30 seconds. Draw away or rinse away undissolved residual product. Always finish by rinsing with clean water. For tough stains, let the product work for 1-10 min, process the stain with a brush and finish with water. ATTENTION! Avoid Mr. Perfect on macrolon, ABS plastic, silk, suede and leather. Unsure if the surface is colorfast or material permanent, try first on a less visible place.
Note: Never apply on hot surfaces and prevent drying.
Use caution on repainted and sensitive metal and plastic surfaces.
Sample washing is recommended.

Dosage

Ready to use, do not dilute

Packaging

224003 – 1L

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Mr Perfect appeared first on Blue and Green.

High-tech coating for linoleum, plastic and rubber floors. The product has excellent chemical resistance properties with high scratch and wear resistance, but also with permanent elasticity. Repeated treatment is possible at any time without stripping. With new technology, ink and graffiti can be easily removed repeatedly, without affecting the surface properties. The product is available with different gloss: high, medium and low gloss.

Advantages

• Restores finishes on worn floors and makes the surface very easy to clean.
• The substrate acquires anti-graffiti properties.
• Provides a protective coating with high gloss.
• Easy to apply to the substrate.
• Only one layer is needed.
• The product provides long-term protection.
• Easy to repair in case of damage.

Application instructions

It is important that the surface is completely clean and free of grease and contaminants. Thoroughly clean the floor and remove stains and old polish. Rinse the surface thoroughly with clean water and allow the surface to dry completely before applying Floor Coating. Linoleum floors may require a long drying time. Check if necessary. with moisture meter that the floor is completely dry. Floor Coating is applied with a microfiber applicator. Apply a thin layer of about 5 μm (micrometers).

NOTE! It is very important to make sure that the material to be coated is not wet or damp. The object temperature must be at least + 10 ° C when the product is applied.

Care: We recommend that you clean a treated floor with a pH-neutral detergent. It prolongs the life of the coating. Normal shelf life is 12-24 months, depending on load and wear. Coverage: 80-100 m2 / L.

Drying times: Dust dry: approx. 20 minutes (+20 C)
Surface dry: approx. 4 hours (+20 C)
Final cured approx. 7 days (+20 C)

Dosage

Used concentrated. NOTE! The product must not be exposed to frost.

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Floor & Wall Coating High Gloss appeared first on Blue and Green.

Orange terpenes are a natural and effective adhesive remover that can be used to remove glue from various surfaces. It contains a natural substance called d-Limonene, which is known for its ability to dissolve fat and adhesive.

Application instructions

To use orange terpenes as an adhesive remover, apply a small amount of oil to the adhesive area and gently rub with a cloth. Let the oil sit for a few minutes to dissolve the adhesive. Then, you can wipe away the oil and adhesive with a clean cloth.

It is important to note that orange terpenes can be strong and may damage certain surfaces, such as plastic. Before using orange terpenes, you should test it on a small hidden area to ensure that it does not cause any damage

Note: Never apply on hot surfaces and prevent drying.
Use caution on repainted and sensitive metal and plastic surfaces.
Sample washing is recommended.

Dosage

It can be used pure or diluted with isopropanol as an orange cleaner.

Packaging

038025 – 25L

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Orange Terpens appeared first on Blue and Green.

Interior Coating is a high-tech transparent 1-component graffiti protection for plastic, colored fiberglass and laminate surfaces. The product has excellent chemical resistance properties with high scratch and abrasion resistance.
Interior Coating is a very effective protection which makes it the natural choice to protect e.g. interior surfaces on trains, metro, trams and buses. Marker, spray and ink paint can be easily and repeatedly removed without affecting the surface.

Advantages

• Permanent graffiti protection
• Protective coating with gloss, easy to apply
• Only 1 layer needs to be applied
• Long durability
• Not flammable

Application instructions

• It is important that the underlying surface is completely clean and free of grease and contaminants.
• Clean the surface thoroughly and remove stains and grease.
• Rinse the surface thoroughly with clean water and let the surface dry completely before applying Interior Coating.
• Interior Coating is preferably applied with a microfiber applicator. Apply a layer of approximately 5 μm (micrometers).

NOTE! It is very important to ensure that the material to be coated is not wet or damp. The object temperature must be at least +5 °C when the product is applied. The product is very sensitive to moisture and film formation can be affected by moisture and low temperatures. Application is carried out according to separate product instructions. Coverage: 125-150 m2 / L.
Drying times: Dust dry: approx. 20 minutes (+20 C), Surface dry: approx. 2 hours (+20 C), Final cured approx. 12 hours (+20 C)

Dosage

Used concentrated. ATTENTION! The product must not be exposed to frost.

Packaging

3871053 – 0,5L

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Interior Coating appeared first on Blue and Green.

Trouble Solver is used to remove paint, ink, spray painting, friction marks, tire marks, glue residue, tar etc.
Trouble Solver can be used on all hard and soft color-resistant surfaces, such as floors, glass, metals, etc.
Can also be used in printing business.
Trouble Solver should not be used on polykarbonat/Lexan/Makrolon, ABS plastic, silk and leather.

Advantages

• Aromatic free
• pH neutral
• Almost odorless

Application instructions

Trouble Solver is applied with a cloth, mop or a lowpressure
equipment. Allow Trouble Solver to work from 10 seconds to 30
minutes, depending on the nature of the substance, and the surface.
If necessary, process the surface with a brush or sponge.
Dry wipe and always rinse with clean water.
If there is any doubt as to whether the surface can withstand
the product, you should do a test in a less visible place.

Dosage

Use concentrated

Packaging

681005 – 5L
681025 – 25L

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Trouble Solver appeared first on Blue and Green.