High-tech coating for linoleum, plastic and rubber floors. The product has excellent chemical resistance properties with high scratch and wear resistance, but also with permanent elasticity. Repeated treatment is possible at any time without stripping. With new technology, ink and graffiti can be easily removed repeatedly, without affecting the surface properties. The product is available with different gloss: high, medium and low gloss.

Advantages

• Restores finishes on worn floors and makes the surface very easy to clean.
• The substrate acquires anti-graffiti properties.
• Provides a protective coating with high gloss.
• Easy to apply to the substrate.
• Only one layer is needed.
• The product provides long-term protection.
• Easy to repair in case of damage.

Application instructions

It is important that the surface is completely clean and free of grease and contaminants. Thoroughly clean the floor and remove stains and old polish. Rinse the surface thoroughly with clean water and allow the surface to dry completely before applying Floor Coating. Linoleum floors may require a long drying time. Check if necessary. with moisture meter that the floor is completely dry. Floor Coating is applied with a microfiber applicator. Apply a thin layer of about 5 μm (micrometers).

NOTE! It is very important to make sure that the material to be coated is not wet or damp. The object temperature must be at least + 10 ° C when the product is applied.

Care: We recommend that you clean a treated floor with a pH-neutral detergent. It prolongs the life of the coating. Normal shelf life is 12-24 months, depending on load and wear. Coverage: 80-100 m2 / L.

Drying times: Dust dry: approx. 20 minutes (+20 C)
Surface dry: approx. 4 hours (+20 C)
Final cured approx. 7 days (+20 C)

Dosage

Used concentrated. NOTE! The product must not be exposed to frost.

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Floor & Wall Coating High Gloss appeared first on Blue and Green.

Interior Coating is a high-tech transparent 1-component graffiti protection for plastic, colored fiberglass and laminate surfaces. The product has excellent chemical resistance properties with high scratch and abrasion resistance.
Interior Coating is a very effective protection which makes it the natural choice to protect e.g. interior surfaces on trains, metro, trams and buses. Marker, spray and ink paint can be easily and repeatedly removed without affecting the surface.

Advantages

• Permanent graffiti protection
• Protective coating with gloss, easy to apply
• Only 1 layer needs to be applied
• Long durability
• Not flammable

Application instructions

• It is important that the underlying surface is completely clean and free of grease and contaminants.
• Clean the surface thoroughly and remove stains and grease.
• Rinse the surface thoroughly with clean water and let the surface dry completely before applying Interior Coating.
• Interior Coating is preferably applied with a microfiber applicator. Apply a layer of approximately 5 μm (micrometers).

NOTE! It is very important to ensure that the material to be coated is not wet or damp. The object temperature must be at least +5 °C when the product is applied. The product is very sensitive to moisture and film formation can be affected by moisture and low temperatures. Application is carried out according to separate product instructions. Coverage: 125-150 m2 / L.
Drying times: Dust dry: approx. 20 minutes (+20 C), Surface dry: approx. 2 hours (+20 C), Final cured approx. 12 hours (+20 C)

Dosage

Used concentrated. ATTENTION! The product must not be exposed to frost.

Packaging

3871053 – 0,5L

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Interior Coating appeared first on Blue and Green.

Cleanon is a low-foaming floor product for polished floors. For
regular cleaning and maintenance of polished floors. An effective
product with great cleaning power, specially developed for cleaning
and maintenance of polished floors and stone flooring. Cleanon can
be used with high speed polishing – excellent polishing qualities.

Advantages

– pH approx. 7.8 in usable solution (1%).
– pH approx. 10 in concentrated form.

Application instructions

Use with all wet-cleaning methods e.g. damp mopping and in floor
washing machines.

The product must not be stored cold.

Dosage

25 to 100 ml per 10 litres water, depending on cleaning frequency
and degree of soiling.
Quick Fix: 1 % per litre water – scrub with machine and red pad.
High speed: 20 % per litre water – With high speed machine.

Packaging

GP-161723 – 5L

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Cleanon appeared first on Blue and Green.

Polly strengthens surfaces Highly durable Contains polyurethane.
Great alkali resistance. For safe treatment of floors in environments with heavy usage and where floors require a new protective top layer.
1 litre can cover 40 to 70 sq. m. Quick drying.
Can be polished at 1500 rpm. Can be removed with Goaway polish remover.

Advantages

– Polyurethane polish.
– Quick drying.

Application instructions

Ensure that floors are cleaned of old polish, polish residue and dirt etc. Spread Polly in a thin layer evenly distributed across the floor
surface. Allow the floor to dry between each treatment/layer.
The surface is dry enough to walk on after approx. 30 minutes. We recommend at least 2-3 thin layers.
For best results, always follow producer’s instructions for the respective flooring materials.

The product must not be stored cold.

Dosage

Spread in a thin layer. Ready to use.
For extra smooth surfaces: spread undiluted in 2-3 thin even layers.

Packaging

GP-161223 – 5L

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Polly appeared first on Blue and Green.

SC Perma is a 1K permanent graffiti protection product that can be used on concrete, brick, wood and metal.

Advantages

– UV resistant and heat resistant
– Open diffusion/breathability
– Low VOC content
– Excellent elastic properties, even at low temperatures
– High water repellent effect
– The product can be applied again on already treated surfaces
– Can be coloured in various shades
– Time-saving and economical to use.
– Clean graffiti with clean water and approx. 100 bar pressure
– No problems with stubborn “graffiti shadows”

Application instructions

• First clean the substrate/underlay carefully for dirt, algae, traffic grime, wax and any colour residue from old graffiti. Allow surface to dry completely.
• Shake or stir product well before use! Apply product with a paint sprayer, low pressure sprayer or roller with a short pile cover in a single layer.
• If the product runs, even out with a paintbrush. The treated surface should have a minimum temperature of approx. 5 °C. Drying time depends on temperature and layer thickness but is fully cured after approx. 24 hours.

NB! After application, the application to ols should be cleaned with Perma Cleaner to prevent the product hardening! Open packages should be used as a film can form after contact with air.

NB! The surface may appear a little darker and shinier after treatment always test a small area to check if the result matches aesthetic expectations.

Dosage

The product is most often used in concentrated form but can be thinned out if needed.
Absorbent surface: 2-4 m2 per litre
Less absorbent surface: 5-8 m2 per litre

Packaging

410009 – 10L

The product image should be seen as an illustration. Some deviation from reality may occur.

The post SC Perma appeared first on Blue and Green.

High-tech coating for linoleum, plastic and rubber floors. The product has excellent chemical resistance properties with high scratch and wear resistance, but also with permanent elasticity. Repeated treatment is possible at any time without stripping. With new technology, ink and graffiti can be easily removed repeatedly, without affecting the surface properties. The product is available with different gloss: high, medium and low gloss.

Advantages

• Restores finishes on worn floors and makes the surface very easy to clean.
• The substrate acquires anti-graffiti properties.
• Provides a protective coating with medium gloss.
• Easy to apply to the substrate.
• Only one layer is needed.
• The product provides long-term protection.
• Easy to repair in case of damage.

Application instructions

It is important that the surface is completely clean and free of grease and contaminants. Thoroughly clean the floor and remove stains and old polish. Rinse the surface thoroughly with clean water and allow the surface to dry completely before applying Floor Coating. Linoleum floors may require a long drying time. Check if necessary. with moisture meter that the floor is completely dry. Floor Coating is applied with a microfiber applicator. Apply a thin layer of about 5 μm (micrometers).

NOTE! It is very important to make sure that the material to be coated is not wet or damp. The object temperature must be at least + 10 ° C when the product is applied.

Care: We recommend that you clean a treated floor with a pH-neutral detergent. It prolongs the life of the coating. Normal life is 12-24 months, depending on load and wear. Coverage: 80-100 m2 / L.

Drying times: Dust dry: approx. 20 minutes (+20 C)
Surface dry: approx. 4 hours (+20 C)
Final cured approx. 7 days (+20 C)

Dosage

Used concentrated. NOTE! The product must not be exposed to frost.

Packaging

3871082 – 0,5L

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Floor & Wall Coating Medium Gloss appeared first on Blue and Green.

DC 6341 is a silane-based sealing agent for concrete.

Advantages

– Effective protection against water and salt damage
– Deep penetration capacity in concrete
– Permeable

Application instructions

Start by cleaning the surface thoroughly to remove dirt and any mould release residue and then allow the surface to dry for 1-5 days depending on the time of year. NB! New concrete must harden for at least 28 days before sealing with DC 6341 is carried out. Shake the product well before use! Apply the sealer using a low-pressure spray gun or roll it on with a roller in a primary layer – then apply a second layer wet on wet to maximise the depth of penetration. The treated surface must have a minimum temperature of approx. 5°C. After approx. 14 days, the anti-graffiti coating can be applied.
Before you begin – Always evaluate the product on each surface to be treated, for suitability and results before overall application. It is important to include previous repairs and repairs in the test area. Different materials / surface compositions can result in absorption and / or appearance differences. Also test the application speed, pattern and technology needed to obtain a smooth surface.
The product cannot be overpainted.

Dosage

The product is used in concentrated form.
Highly absorbent surfaces: 2-3 m2 per litre
Less absorbent surfaces: 4-5 m2 per litre

Packaging

3062025 – 25L

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Silane DC 6341 40% appeared first on Blue and Green.

SC 20 is a patented environmentally adapted polysaccharide-based anti-graffiti coating that can be used on most types of absorbent surfaces, including brick, concrete, granite, sandstone, limestone, plaster etc.

Advantages

– Protects against spray paint, paintbrush and marker graffiti
– Prevents occurrence of hard to clean “graffiti shadows”
– Low melting point
– Permeable
– Estimated lifetime of approx. 36 months, depending on the surface and external influences.
– Recommended for historical monuments and listed building facades as the pro-duct has fantastic aesthetic advantages – completely invisible but provides the surface with the necessary protection.

Application instructions

Start by cleaning the surface thoroughly to remove dirt, algae, traffic film, wax, and any paint remnants from old graffiti.
Allow the surface to dry so that it is dry or slightly damp but not wet. NB! New concrete must harden for a minimum of 28 days before e the anti-graffiti coating is applied.
When applying anti-graffiti coating to newly painted surfaces, allow the paint to dry for approx. 2 – 4 weeks before application takes place. Shake the product well before use! Apply the product using an airless spray gun or roll it on with a roller. If the product runs, even it out with a paintbrush.
The coating should be applied in 2-3 layers and the first layer must be dry before the next layer is applied (usually 30 minutes – 1 hour).
The treated surface must have a minimum temperature of approx. 5°C. Drying time is 1-3 hours depending on the temperature.
After treatment, it is easier to remove graffiti or other undesired residues with a pressure washer (60-90 bar) and hot water (approx. 65°C). Adjust pressure to the surface/facade.
2-3 new layers of the product are then applied to the cleaned surface, which is subsequently protected against graffiti again.

Before you begin – Always evaluate the product on each surface to be treated, for suitability and results before overall application. It is important to include previous repairs and repairs in the test area. Different materials / surface compositions can result in absorption and / or appearance differences. Also test the application speed, pattern and technology needed to obtain a smooth surface.

Dosage

The product is used in concentrated form. Highly absorbent surfaces: 3-4 dl each m2. Less absorbent surfaces: 1-2 dl each layer. (2-3 layers are recommended).

Packaging

306015 – 15L

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Naturacoat SC 20 appeared first on Blue and Green.

Graffiti Shield Colour is a pigmented water-based wax emulsion that can be used as a combined anti-graffiti coating and coverage pro-
duct on trains, in underpasses and overpasses.

Advantages

– Permeable
– Hides severe graffiti immediately until cleaning is possible
– Hides and restores overcleaned surfaces
– Low melting point
– Can be pigmented in the desired RAL or NCS colour standard

Application instructions

Start by cleaning the surface thoroughly to remove dirt. Allow the surface to dry properly.
The product must be stirred well before use! Apply the product using a roller or airless spray gun in 1-2 layers.
It is important that the first layer is allowed to dry before a second layer is applied. If the product runs, even it out with a paintbrush. The treated surface must have a minimum temperature of approx. 5°C. Drying time depends on the temperature.
After treatment, it is easier to remove graffiti or other undesired residues with a pressure washer (70-150 bar) and hot water (approx. 70°C).
Re-apply 1-2 layers of the coating to the cleaned surface.

Before you begin – Always evaluate the product on each surface to be treated, for suitability and results before overall application. It is important to include previous repairs and repairs in the test area. Different materials / surface compositions can result in absorption and / or appearance differences. Also test the application speed, pattern and technology needed to obtain a smooth surface.

Dosage

The product is used in concentrated form. Consumption approx. 0.3 – 0.5 litre per m2.

Packaging

305111 – 10L

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Graffiti Shield Color Betong appeared first on Blue and Green.

DC 6683 is waterbased silane/siloxane solution that is used for the sealing of mineral facade surfaces and concrete.

Advantages

– Effective protection against water damage – Permeable – UV resistant – Extends cleaning interval – Estimated lifetime of approx. 10 years

Application instructions

Start by cleaning the surface thoroughly to remove dirt and then allow the surface to dry. Make sure to cover windows and other surfaces that are not being treated. Shake the product well before use! Apply the sealer using an airless or low-pressure sprayer or roll it on with a roller in a first layer, going slowly from the top down, and then apply a second layer wet-on-wet to maximise the effect of the product. The treated surface must have a minimum temperature of approx. 5°C. After approx. 7 days, the anti-graffiti coating can be applied.
Before you begin – Always evaluate the product on each surface to be treated, for suitability and results before overall application. It is important to include previous repairs and repairs in the test area. Different materials / surface compositions can result in absorption and / or appearance differences. Also test the application speed, pattern and technology needed to obtain a smooth surface.
The product cannot be overpainted.

Dosage

The product is used in concentrated form.
Highly absorbent surfaces: 1 – 3 m2 per litre
Less absorbent surfaces: 4 – 5 m2 per litre

Packaging

302025 – 25L
302700 – 1000L

The product image should be seen as an illustration. Some deviation from reality may occur.

The post Silane DC 6683 appeared first on Blue and Green.